DDOS 是十分常见的攻击，即使是一般使用者，下载一套 DDOS 软件，或者直接安装 kali linux, 便可以很简单发动 DDOS 攻击，除了遇到 DDOS 攻击才采取拦截外，也可以透过一些 Linux 设定来预防 DDOS 攻击，以下会列出一些预防 DDOS 的设定及 Firewalld 规则。
Firewalld 限制每个 IP 连线数量
以下会设定 Firewalld 限制每个 IP 在 60 秒内, 只可以建立 30 个 HTTP (port 80) 连线, 以下两个参数可以根据自己的需要作出调整。
先建立档案 /etc/modprobe.d/xt.conf:
vi /etc/modprobe.d/xt.conf
加入以下内容:
options xt_recent ip_pkt_list_tot=30
在 vi 储存盘案及离开:
:wq
然后加载 xt_recent 模组:
# modprobe xt_recent
然后执行以下 firewall 指令:
# /bin/firewall-cmd –permanent –direct –add-rule ipv4 filter INPUT_direct \
0 -p tcp –dport 80 -m state –state NEW -m recent –set
0 -p tcp –dport 80 -m state –state NEW -m recent –set
# /bin/firewall-cmd –permanent –direct –add-rule ipv4 filter INPUT_direct \
1 -p tcp –dport 80 -m state –state NEW -m recent –update \
–seconds 60 –hitcount 30 -j REJECT –reject-with tcp-reset
1 -p tcp –dport 80 -m state –state NEW -m recent –update \
–seconds 60 –hitcount 30 -j REJECT –reject-with tcp-reset
# firewall-cmd –reload
设定好后, 可以检视一下 firewalld 规则是否加入成功:
# firewall-cmd –permanent –direct –get-all-rules
Linux Kernel
透过修改 Linux Kernel 的设定，同样可以有效减低 DDOS 的威胁，RHEL 7 及 CentOS 7 支援 SYNPROXY 设定，以下会以 CentOS 7 为例，透过修改 Kernel 的参数来减低 DDOS 的威胁。
开启档案 /etc/sysctl.conf，加入以下设定：
kernel.printk = 4 4 1 7
kernel.panic = 10
kernel.sysrq = 0
kernel.shmmax = 4294967296
kernel.shmall = 4194304
kernel.core_uses_pid = 1
kernel.msgmnb = 65536
kernel.msgmax = 65536
vm.swappiness = 20
vm.dirty_ratio = 80
vm.dirty_background_ratio = 5
fs.file-max = 2097152
net.core.netdev_max_backlog = 262144
net.core.rmem_default = 31457280
net.core.rmem_max = 67108864
net.core.wmem_default = 31457280
net.core.wmem_max = 67108864
net.core.somaxconn = 65535
net.core.optmem_max = 25165824
net.ipv4.neigh.default.gc_thresh1 = 4096
net.ipv4.neigh.default.gc_thresh2 = 8192
net.ipv4.neigh.default.gc_thresh3 = 16384
net.ipv4.neigh.default.gc_interval = 5
net.ipv4.neigh.default.gc_stale_time = 120
net.netfilter.nf_conntrack_max = 10000000
net.netfilter.nf_conntrack_tcp_loose = 0
net.netfilter.nf_conntrack_tcp_timeout_established = 1800
net.netfilter.nf_conntrack_tcp_timeout_close = 10
net.netfilter.nf_conntrack_tcp_timeout_close_wait = 10
net.netfilter.nf_conntrack_tcp_timeout_fin_wait = 20
net.netfilter.nf_conntrack_tcp_timeout_last_ack = 20
net.netfilter.nf_conntrack_tcp_timeout_syn_recv = 20
net.netfilter.nf_conntrack_tcp_timeout_syn_sent = 20
net.netfilter.nf_conntrack_tcp_timeout_time_wait = 10
net.ipv4.tcp_slow_start_after_idle = 0
net.ipv4.ip_local_port_range = 1024 65000
net.ipv4.ip_no_pmtu_disc = 1
net.ipv4.route.flush = 1
net.ipv4.route.max_size = 8048576
net.ipv4.icmp_echo_ignore_broadcasts = 1
net.ipv4.icmp_ignore_bogus_error_responses = 1
net.ipv4.tcp_congestion_control = htcp
net.ipv4.tcp_mem = 65536 131072 262144
net.ipv4.udp_mem = 65536 131072 262144
net.ipv4.tcp_rmem = 4096 87380 33554432
net.ipv4.udp_rmem_min = 16384
net.ipv4.tcp_wmem = 4096 87380 33554432
net.ipv4.udp_wmem_min = 16384
net.ipv4.tcp_max_tw_buckets = 1440000
net.ipv4.tcp_tw_recycle = 0
net.ipv4.tcp_tw_reuse = 1
net.ipv4.tcp_max_orphans = 400000
net.ipv4.tcp_window_scaling = 1
net.ipv4.tcp_rfc1337 = 1
net.ipv4.tcp_syncookies = 1
net.ipv4.tcp_synack_retries = 1
net.ipv4.tcp_syn_retries = 2
net.ipv4.tcp_max_syn_backlog = 16384
net.ipv4.tcp_timestamps = 1
net.ipv4.tcp_sack = 1
net.ipv4.tcp_fack = 1
net.ipv4.tcp_ecn = 2
net.ipv4.tcp_fin_timeout = 10
net.ipv4.tcp_keepalive_time = 600
net.ipv4.tcp_keepalive_intvl = 60
net.ipv4.tcp_keepalive_probes = 10
net.ipv4.tcp_no_metrics_save = 1
net.ipv4.ip_forward = 0
net.ipv4.conf.all.accept_redirects = 0
net.ipv4.conf.all.send_redirects = 0
net.ipv4.conf.all.accept_source_route = 0
net.ipv4.conf.all.rp_filter = 1
kernel.panic = 10
kernel.sysrq = 0
kernel.shmmax = 4294967296
kernel.shmall = 4194304
kernel.core_uses_pid = 1
kernel.msgmnb = 65536
kernel.msgmax = 65536
vm.swappiness = 20
vm.dirty_ratio = 80
vm.dirty_background_ratio = 5
fs.file-max = 2097152
net.core.netdev_max_backlog = 262144
net.core.rmem_default = 31457280
net.core.rmem_max = 67108864
net.core.wmem_default = 31457280
net.core.wmem_max = 67108864
net.core.somaxconn = 65535
net.core.optmem_max = 25165824
net.ipv4.neigh.default.gc_thresh1 = 4096
net.ipv4.neigh.default.gc_thresh2 = 8192
net.ipv4.neigh.default.gc_thresh3 = 16384
net.ipv4.neigh.default.gc_interval = 5
net.ipv4.neigh.default.gc_stale_time = 120
net.netfilter.nf_conntrack_max = 10000000
net.netfilter.nf_conntrack_tcp_loose = 0
net.netfilter.nf_conntrack_tcp_timeout_established = 1800
net.netfilter.nf_conntrack_tcp_timeout_close = 10
net.netfilter.nf_conntrack_tcp_timeout_close_wait = 10
net.netfilter.nf_conntrack_tcp_timeout_fin_wait = 20
net.netfilter.nf_conntrack_tcp_timeout_last_ack = 20
net.netfilter.nf_conntrack_tcp_timeout_syn_recv = 20
net.netfilter.nf_conntrack_tcp_timeout_syn_sent = 20
net.netfilter.nf_conntrack_tcp_timeout_time_wait = 10
net.ipv4.tcp_slow_start_after_idle = 0
net.ipv4.ip_local_port_range = 1024 65000
net.ipv4.ip_no_pmtu_disc = 1
net.ipv4.route.flush = 1
net.ipv4.route.max_size = 8048576
net.ipv4.icmp_echo_ignore_broadcasts = 1
net.ipv4.icmp_ignore_bogus_error_responses = 1
net.ipv4.tcp_congestion_control = htcp
net.ipv4.tcp_mem = 65536 131072 262144
net.ipv4.udp_mem = 65536 131072 262144
net.ipv4.tcp_rmem = 4096 87380 33554432
net.ipv4.udp_rmem_min = 16384
net.ipv4.tcp_wmem = 4096 87380 33554432
net.ipv4.udp_wmem_min = 16384
net.ipv4.tcp_max_tw_buckets = 1440000
net.ipv4.tcp_tw_recycle = 0
net.ipv4.tcp_tw_reuse = 1
net.ipv4.tcp_max_orphans = 400000
net.ipv4.tcp_window_scaling = 1
net.ipv4.tcp_rfc1337 = 1
net.ipv4.tcp_syncookies = 1
net.ipv4.tcp_synack_retries = 1
net.ipv4.tcp_syn_retries = 2
net.ipv4.tcp_max_syn_backlog = 16384
net.ipv4.tcp_timestamps = 1
net.ipv4.tcp_sack = 1
net.ipv4.tcp_fack = 1
net.ipv4.tcp_ecn = 2
net.ipv4.tcp_fin_timeout = 10
net.ipv4.tcp_keepalive_time = 600
net.ipv4.tcp_keepalive_intvl = 60
net.ipv4.tcp_keepalive_probes = 10
net.ipv4.tcp_no_metrics_save = 1
net.ipv4.ip_forward = 0
net.ipv4.conf.all.accept_redirects = 0
net.ipv4.conf.all.send_redirects = 0
net.ipv4.conf.all.accept_source_route = 0
net.ipv4.conf.all.rp_filter = 1
储存盘案后，重新开机会自动加载新参数设定，也可以输入以下指令重新加载 /etc/sysctl.conf 的设定，而无需重新开机：
# sysctl –system